ServiceNow Certified System Administrator – Exam 2022

2 Full Practice Test + 1 Bonus with Explanations included!

Are you an Electrical Engineer??? If Yes Take Following Quiz

Electrical Engineering

Smart Series Quiz-1

These questions are taken from smart series book which covers all the subjects of Electrical Engineering and Technology Field

1 / 30

Category: Network Analysis

1) Admittance is the reciprocal of

a) Capacitive reactance

b) Inductive reactance

c) Reactive power

d) Impedance

2 / 30

Category: Singal and Systems

2) The _____ time signal is described for all values of time.

a) Discrete

b) Continuous

c) Random

d) Digital

3 / 30

Category: Power Plant

3) The average fossil fuel plant convers about is ______ % of the power going in to the power going out.

a) 33

b) 40

c) 25

d) 50

4 / 30

Category: Basic Electrical Engineering

4) Conjunction x ^ y behaves on digits 0 and 1 exactly as ____ does for ordinary algebra.

a) Addition

b) Subtraction

c) Multiplication

d) Division

5 / 30

Category: Electroncis

5) A semiconductor device is connected in a series circuit with a battery and a resistance. If the polarity of battery is reversed, the current drops almost to zero. The device may be

a) P-type semiconductor

b) N-type semiconductor

c) P-N junction

d) An intrinsic semiconductor

6 / 30

Category: Power System Analysis

6) There are ____ types of dependent sources, depending on the controlling variable and output of the source.

a) Two

b) Three

c) Four

d) Five

7 / 30

Category: Power Electroncis

7) If the firing angle in an SCR rectifier is decreased, output will be

a) Maximum

b) Increased

c) Decreased

d) Unaffected

8 / 30

Category: Basic Electrical Engineering

8) If the input capacitor of a power supply is shorted, it will result in

a) Excessive hum

b) Reduced voltage output

c) No voltage output

d) Low voltage output

9 / 30

Category: Electrical Machines

9) A transformer transforms

a) Voltage

b) Power

c) Frequency

d) Current

e) Both A & D

10 / 30

Category: Power System Analysis

10) The quantity "Rm" which relates dependent voltage to controlling current is called

a) Trans Conductance

b) Maximum Resistance

c) Trans Resistance

d) Limiting Resistance

11 / 30

Category: Telecommunications

11) Modulation index in amplitude modulation

a) Is defined as the measure of extent of amplitude variation about an un-modulated carrier.

b) Does not impact power dissipation

c) Is independent of integral multiple of amplitude

d) None of these

12 / 30

Category: Power Plant

12) ______ is a by-product of paper industry, which is used by many industries as a primary source of electricity.

a) Landfill gas

b) Sludge waste

c) Black Liquor

d) Wood waste

13 / 30

Category: Power Plant

13) If field resistance of DC shunt generator is increased beyond its critical value, the generator

a) output voltage will exceed its nameplate rating

b) will not build up

c) may burn out if loaded to its nameplate rating

d) power output may exceed its nameplate rating

14 / 30

Category: Singal and Systems

14) Main purpose of modulation process is to

a) Distort the original signal

b) Add extra noise to the signal

c) Reduce the mutual interference

d) Time shift in frequency

e) Increase signal to noise ratio

15 / 30

Category: Power System Analysis

15) Power in AC circuit is found by

a) VI sin (phi)

b) VI tan (phi)

c) VI cos (phi)

d) VI

16 / 30

Category: Probability

16) What is the probability of a number "2" when a dice is thrown?

a) 2/6

b) 1/3

c) 1/6

d) 1/4

17 / 30

Category: Basic Electrical Engineering

17) At very sunny places this source(s) of energy can be found

a) Jet fuel

b) Geothermal

c) Solar

d) Both B & C

18 / 30

Category: Power Transmission and Distributions

18) Drop out to cut off ratio for most relays is of the order of

a) 0.2 to 0.3

b) 0.3 to 0.4

c) 0.4 to 0.6

d) 0.6 to 1.0

19 / 30

Category: Power Transmission and Distributions

19) For which purpose bundled conductors are employed to a power system

a) Appearance of the transmission line

b) Mechanical stability of the line

c) Decrease system stability

d) Increase the short circuit current

20 / 30

Category: Basic Electrical Engineering

20) Which line is obtained by the method of least square?

a) Straight line

b) Second degree equation line

c) Polynomial equation line

d) Best fit line

We have to maintain flatness of the surface.

21 / 30

Category: Power System Analysis

21) Which of the following are considered as disadvantages(s) of Gauss-Seidel method over Newton Raphson method in load flow analysis?

a) More iteration

b) More memory requirement and less accuracy

c) Less iteration but more memory

d) More accuracy and more memory

22 / 30

Category: Electroncis

22) SCR (Silicon Controlled Rectifier) goes into saturation, when gate-cathode junction is

a) Forward biased

b) Reversed biased

c) In steady state

d) Polarized

23 / 30

Category: Electrical Machines

23) Radio frequency chokes are air cored to

a) Keep frequency low

b) Keep inductive reactance low

c) Keep frequency high

d) Keep inductive reactance high

24 / 30

Category: Electrical Machines

24) Fundamental property used in single node pair circuit analyzer is that ______ across all elements is same.

a) Current

b) Voltage

c) Resistance

d) Inductance

25 / 30

Category: Electroncis

25) Discrete device field effect transistor is classified on the basis of their

a) Resistive state

b) Conducting state

c) Voltaic state

d) Control gate construction

We have to maintain flatness of the surface.

26 / 30

Category: DC Machines

26) The Pole Shoes of DC Machines are fastened to the pole core by:

a) Welding

b) Soldering

c) Countersunk Screws

d) Steel Clumps

27 / 30

Category: Basic Electrical Engineering

27) Fourier series are infinite series of elementary trigonometric functions i.e. Sine and

a) Cosine

b) Sec

c) Cosec

d) Tan

28 / 30

Category: Power System Analysis

28) Which of the following ideas means deciding at runtime what strategy to summon?

a) Dynamic typing

b) Dynamic hiding

c) Dynamic loading

d) Dynamic blinding

29 / 30

Category: Power Transmission and Distributions

29) Which of the following conditions relate line resistance 'R' and line reactance 'X' for maximum steady state power transmission on a transmission line?

a) X=R

b) R=[Square Root (3)]*X

c) X=[Square Root (3)]*R

d) X=R / [Square Root (3)]

30 / 30

Category: Power Plant

30) Landfill gas is actually _______ used in thermal power plants.

a) Methane

b) Ethane

c) Black Liquor

d) Phosphorus

Your score is

The average score is 28%

Free Udemy Course With Certification
Free certification course for student so that he can enlarge his skills and get certification
📣 Note: All Courses Are Free For 1000 Enrolls Only. After That Coupons Will Not Apply. So Enroll Course ASAP

This post appeared first on Udemy Free Udemy Courses | 1000FF Udemy Coupons.

00Days
00Hours
00Minutes
00Seconds

Enroll Now Free

Find More Courses

ServiceNow Certified System Administrator – Exam 2022

Are you an Electrical Engineer??? If Yes Take Following Quiz

Like this:

Related

Leave a Comment Cancel Reply

Are you an Electrical Engineer??? If Yes Take Following Quiz

Share this:

Like this:

Related

Leave a Comment Cancel Reply