Post Views: 4

Professional Financial Analyst Assessment (PFAA)

Financial Analyst Certification by The Retail Banking School and preparing for certification of other providers

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

If YOU are an Electrical Engineer then following quiz is for YOU

Electrical Engineering

Smart Series Quiz-1

These questions are taken from smart series book which covers all the subjects of Electrical Engineering and Technology Field

1 / 30

Category: Electrical Machines

1) Fundamental property used in single node pair circuit analyzer is that ______ across all elements is same.

a) Current

b) Voltage

c) Resistance

d) Inductance

2 / 30

Category: Power System Analysis

2) Which of the following ideas means deciding at runtime what strategy to summon?

a) Dynamic typing

b) Dynamic hiding

c) Dynamic loading

d) Dynamic blinding

3 / 30

Category: Electrical Machines

3) Radio frequency chokes are air cored to

a) Keep frequency low

b) Keep inductive reactance low

c) Keep frequency high

d) Keep inductive reactance high

We have to maintain flatness of the surface.

4 / 30

Category: Power System Analysis

4) Which of the following are considered as disadvantages(s) of Gauss-Seidel method over Newton Raphson method in load flow analysis?

a) More iteration

b) More memory requirement and less accuracy

c) Less iteration but more memory

d) More accuracy and more memory

5 / 30

Category: Power Plant

5) The average fossil fuel plant convers about is ______ % of the power going in to the power going out.

a) 33

b) 40

c) 25

d) 50

6 / 30

Category: Telecommunications

6) Modulation index in amplitude modulation

a) Is defined as the measure of extent of amplitude variation about an un-modulated carrier.

b) Does not impact power dissipation

c) Is independent of integral multiple of amplitude

d) None of these

7 / 30

Category: Network Analysis

7) Admittance is the reciprocal of

a) Capacitive reactance

b) Inductive reactance

c) Reactive power

d) Impedance

We have to maintain flatness of the surface.

8 / 30

Category: DC Machines

8) The Pole Shoes of DC Machines are fastened to the pole core by:

a) Welding

b) Soldering

c) Countersunk Screws

d) Steel Clumps

9 / 30

Category: Power Plant

9) ______ is a by-product of paper industry, which is used by many industries as a primary source of electricity.

a) Landfill gas

b) Sludge waste

c) Black Liquor

d) Wood waste

10 / 30

Category: Power Plant

10) Landfill gas is actually _______ used in thermal power plants.

a) Methane

b) Ethane

c) Black Liquor

d) Phosphorus

11 / 30

Category: Basic Electrical Engineering

11) At very sunny places this source(s) of energy can be found

a) Jet fuel

b) Geothermal

c) Solar

d) Both B & C

12 / 30

Category: Basic Electrical Engineering

12) Fourier series are infinite series of elementary trigonometric functions i.e. Sine and

a) Cosine

b) Sec

c) Cosec

d) Tan

13 / 30

Category: Power Transmission and Distributions

13) Drop out to cut off ratio for most relays is of the order of

a) 0.2 to 0.3

b) 0.3 to 0.4

c) 0.4 to 0.6

d) 0.6 to 1.0

14 / 30

Category: Power System Analysis

14) The quantity “Rm” which relates dependent voltage to controlling current is called

a) Trans Conductance

b) Maximum Resistance

c) Trans Resistance

d) Limiting Resistance

15 / 30

Category: Electroncis

15) SCR (Silicon Controlled Rectifier) goes into saturation, when gate-cathode junction is

a) Forward biased

b) Reversed biased

c) In steady state

d) Polarized

16 / 30

Category: Electroncis

16) A semiconductor device is connected in a series circuit with a battery and a resistance. If the polarity of battery is reversed, the current drops almost to zero. The device may be

a) P-type semiconductor

b) N-type semiconductor

c) P-N junction

d) An intrinsic semiconductor

17 / 30

Category: Electrical Machines

17) A transformer transforms

a) Voltage

b) Power

c) Frequency

d) Current

e) Both A & D

18 / 30

Category: Power System Analysis

18) Power in AC circuit is found by

a) VI sin (phi)

b) VI tan (phi)

c) VI cos (phi)

d) VI

19 / 30

Category: Basic Electrical Engineering

19) Conjunction x ^ y behaves on digits 0 and 1 exactly as ____ does for ordinary algebra.

a) Addition

b) Subtraction

c) Multiplication

d) Division

20 / 30

Category: Basic Electrical Engineering

20) If the input capacitor of a power supply is shorted, it will result in

a) Excessive hum

b) Reduced voltage output

c) No voltage output

d) Low voltage output

21 / 30

Category: Probability

21) What is the probability of a number “2” when a dice is thrown?

a) 2/6

b) 1/3

c) 1/6

d) 1/4

22 / 30

Category: Singal and Systems

22) Main purpose of modulation process is to

a) Distort the original signal

b) Add extra noise to the signal

c) Reduce the mutual interference

d) Time shift in frequency

e) Increase signal to noise ratio

23 / 30

Category: Electroncis

23) Discrete device field effect transistor is classified on the basis of their

a) Resistive state

b) Conducting state

c) Voltaic state

d) Control gate construction

24 / 30

Category: Power Plant

24) If field resistance of DC shunt generator is increased beyond its critical value, the generator

a) output voltage will exceed its nameplate rating

b) will not build up

c) may burn out if loaded to its nameplate rating

d) power output may exceed its nameplate rating

25 / 30

Category: Power Electroncis

25) If the firing angle in an SCR rectifier is decreased, output will be

a) Maximum

b) Increased

c) Decreased

d) Unaffected

26 / 30

Category: Power System Analysis

26) There are ____ types of dependent sources, depending on the controlling variable and output of the source.

a) Two

b) Three

c) Four

d) Five

27 / 30

Category: Singal and Systems

27) The _____ time signal is described for all values of time.

a) Discrete

b) Continuous

c) Random

d) Digital

28 / 30

Category: Power Transmission and Distributions

28) For which purpose bundled conductors are employed to a power system

a) Appearance of the transmission line

b) Mechanical stability of the line

c) Decrease system stability

d) Increase the short circuit current

29 / 30

Category: Basic Electrical Engineering

29) Which line is obtained by the method of least square?

a) Straight line

b) Second degree equation line

c) Polynomial equation line

d) Best fit line

30 / 30

Category: Power Transmission and Distributions

30) Which of the following conditions relate line resistance ‘R’ and line reactance ‘X’ for maximum steady state power transmission on a transmission line?

a) X=R

b) R=[Square Root (3)]*X

c) X=[Square Root (3)]*R

d) X=R / [Square Root (3)]