Memory: 3 Ways of Memorising Like a Spy

Let’s jog your Memory and make it even better that it was before!

1000 Coupons are used

24 hours passed

If YOU are an Electrical Engineer then following quiz is for YOU

Electrical Engineering

Smart Series Quiz-1

These questions are taken from smart series book which covers all the subjects of Electrical Engineering and Technology Field

1 / 30

Category: Basic Electrical Engineering

1) At very sunny places this source(s) of energy can be found

a) Jet fuel

b) Geothermal

c) Solar

d) Both B & C

2 / 30

Category: Singal and Systems

2) Main purpose of modulation process is to

a) Distort the original signal

b) Add extra noise to the signal

c) Reduce the mutual interference

d) Time shift in frequency

e) Increase signal to noise ratio

3 / 30

Category: Power System Analysis

3) There are ____ types of dependent sources, depending on the controlling variable and output of the source.

a) Two

b) Three

c) Four

d) Five

4 / 30

Category: Power Plant

4) The average fossil fuel plant convers about is ______ % of the power going in to the power going out.

a) 33

b) 40

c) 25

d) 50

5 / 30

Category: Basic Electrical Engineering

5) If the input capacitor of a power supply is shorted, it will result in

a) Excessive hum

b) Reduced voltage output

c) No voltage output

d) Low voltage output

6 / 30

Category: Power Transmission and Distributions

6) Which of the following conditions relate line resistance ‘R’ and line reactance ‘X’ for maximum steady state power transmission on a transmission line?

a) X=R

b) R=[Square Root (3)]*X

c) X=[Square Root (3)]*R

d) X=R / [Square Root (3)]

7 / 30

Category: Electroncis

7) SCR (Silicon Controlled Rectifier) goes into saturation, when gate-cathode junction is

a) Forward biased

b) Reversed biased

c) In steady state

d) Polarized

8 / 30

Category: Power System Analysis

8) The quantity “Rm” which relates dependent voltage to controlling current is called

a) Trans Conductance

b) Maximum Resistance

c) Trans Resistance

d) Limiting Resistance

9 / 30

Category: Telecommunications

9) Modulation index in amplitude modulation

a) Is defined as the measure of extent of amplitude variation about an un-modulated carrier.

b) Does not impact power dissipation

c) Is independent of integral multiple of amplitude

d) None of these

10 / 30

Category: Basic Electrical Engineering

10) Conjunction x ^ y behaves on digits 0 and 1 exactly as ____ does for ordinary algebra.

a) Addition

b) Subtraction

c) Multiplication

d) Division

11 / 30

Category: Power Plant

11) If field resistance of DC shunt generator is increased beyond its critical value, the generator

a) output voltage will exceed its nameplate rating

b) will not build up

c) may burn out if loaded to its nameplate rating

d) power output may exceed its nameplate rating

12 / 30

Category: Network Analysis

12) Admittance is the reciprocal of

a) Capacitive reactance

b) Inductive reactance

c) Reactive power

d) Impedance

13 / 30

Category: Basic Electrical Engineering

13) Which line is obtained by the method of least square?

a) Straight line

b) Second degree equation line

c) Polynomial equation line

d) Best fit line

14 / 30

Category: Probability

14) What is the probability of a number “2” when a dice is thrown?

a) 2/6

b) 1/3

c) 1/6

d) 1/4

15 / 30

Category: Electroncis

15) A semiconductor device is connected in a series circuit with a battery and a resistance. If the polarity of battery is reversed, the current drops almost to zero. The device may be

a) P-type semiconductor

b) N-type semiconductor

c) P-N junction

d) An intrinsic semiconductor

16 / 30

Category: Power Transmission and Distributions

16) Drop out to cut off ratio for most relays is of the order of

a) 0.2 to 0.3

b) 0.3 to 0.4

c) 0.4 to 0.6

d) 0.6 to 1.0

17 / 30

Category: Power Electroncis

17) If the firing angle in an SCR rectifier is decreased, output will be

a) Maximum

b) Increased

c) Decreased

d) Unaffected

18 / 30

Category: Singal and Systems

18) The _____ time signal is described for all values of time.

a) Discrete

b) Continuous

c) Random

d) Digital

19 / 30

Category: Power System Analysis

19) Power in AC circuit is found by

a) VI sin (phi)

b) VI tan (phi)

c) VI cos (phi)

d) VI

20 / 30

Category: Electrical Machines

20) Fundamental property used in single node pair circuit analyzer is that ______ across all elements is same.

a) Current

b) Voltage

c) Resistance

d) Inductance

21 / 30

Category: Power Plant

21) ______ is a by-product of paper industry, which is used by many industries as a primary source of electricity.

a) Landfill gas

b) Sludge waste

c) Black Liquor

d) Wood waste

22 / 30

Category: Electrical Machines

22) A transformer transforms

a) Voltage

b) Power

c) Frequency

d) Current

e) Both A & D

23 / 30

Category: Electrical Machines

23) Radio frequency chokes are air cored to

a) Keep frequency low

b) Keep inductive reactance low

c) Keep frequency high

d) Keep inductive reactance high

24 / 30

Category: Basic Electrical Engineering

24) Fourier series are infinite series of elementary trigonometric functions i.e. Sine and

a) Cosine

b) Sec

c) Cosec

d) Tan

We have to maintain flatness of the surface.

25 / 30

Category: DC Machines

25) The Pole Shoes of DC Machines are fastened to the pole core by:

a) Welding

b) Soldering

c) Countersunk Screws

d) Steel Clumps

26 / 30

Category: Power Plant

26) Landfill gas is actually _______ used in thermal power plants.

a) Methane

b) Ethane

c) Black Liquor

d) Phosphorus

We have to maintain flatness of the surface.

27 / 30

Category: Power System Analysis

27) Which of the following are considered as disadvantages(s) of Gauss-Seidel method over Newton Raphson method in load flow analysis?

a) More iteration

b) More memory requirement and less accuracy

c) Less iteration but more memory

d) More accuracy and more memory

28 / 30

Category: Electroncis

28) Discrete device field effect transistor is classified on the basis of their

a) Resistive state

b) Conducting state

c) Voltaic state

d) Control gate construction

29 / 30

Category: Power Transmission and Distributions

29) For which purpose bundled conductors are employed to a power system

a) Appearance of the transmission line

b) Mechanical stability of the line

c) Decrease system stability

d) Increase the short circuit current

30 / 30

Category: Power System Analysis

30) Which of the following ideas means deciding at runtime what strategy to summon?

a) Dynamic typing

b) Dynamic hiding

c) Dynamic loading

d) Dynamic blinding

Your score is

The average score is 28%

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

Enroll Now

More Courses

Memory: 3 Ways of Memorising Like a Spy

1000 Coupons are used

24 hours passed

If YOU are an Electrical Engineer then following quiz is for YOU

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

Like this:

Related

Leave a Comment Cancel Reply

Memory: 3 Ways of Memorising Like a Spy

1000 Coupons are used

24 hours passed

If YOU are an Electrical Engineer then following quiz is for YOU

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

Share this:

Like this:

Related

Leave a Comment Cancel Reply