Live Streaming – The Complete Course

Post Views: 2

Live Streaming Like a Pro – Learn Tech and Performance Skills for Zoom Meetings – Twitch – OBS – Open Broadcaster – FB

Are you an Electrical Engineer??? If Yes Take Following Quiz

Electrical Engineering

Smart Series Quiz-1

These questions are taken from smart series book which covers all the subjects of Electrical Engineering and Technology Field

1 / 30

Category: Power Plant

1) Landfill gas is actually _______ used in thermal power plants.

a) Methane

b) Ethane

c) Black Liquor

d) Phosphorus

2 / 30

Category: Power Transmission and Distributions

2) Which of the following conditions relate line resistance 'R' and line reactance 'X' for maximum steady state power transmission on a transmission line?

a) X=R

b) R=[Square Root (3)]*X

c) X=[Square Root (3)]*R

d) X=R / [Square Root (3)]

3 / 30

Category: Electrical Machines

3) Radio frequency chokes are air cored to

a) Keep frequency low

b) Keep inductive reactance low

c) Keep frequency high

d) Keep inductive reactance high

4 / 30

Category: Power Plant

4) The average fossil fuel plant convers about is ______ % of the power going in to the power going out.

a) 33

b) 40

c) 25

d) 50

5 / 30

Category: Basic Electrical Engineering

5) Conjunction x ^ y behaves on digits 0 and 1 exactly as ____ does for ordinary algebra.

a) Addition

b) Subtraction

c) Multiplication

d) Division

6 / 30

Category: Electroncis

6) Discrete device field effect transistor is classified on the basis of their

a) Resistive state

b) Conducting state

c) Voltaic state

d) Control gate construction

7 / 30

Category: Power Plant

7) ______ is a by-product of paper industry, which is used by many industries as a primary source of electricity.

a) Landfill gas

b) Sludge waste

c) Black Liquor

d) Wood waste

8 / 30

Category: Power System Analysis

8) Which of the following ideas means deciding at runtime what strategy to summon?

a) Dynamic typing

b) Dynamic hiding

c) Dynamic loading

d) Dynamic blinding

9 / 30

Category: Power System Analysis

9) There are ____ types of dependent sources, depending on the controlling variable and output of the source.

a) Two

b) Three

c) Four

d) Five

10 / 30

Category: Singal and Systems

10) Main purpose of modulation process is to

a) Distort the original signal

b) Add extra noise to the signal

c) Reduce the mutual interference

d) Time shift in frequency

e) Increase signal to noise ratio

11 / 30

Category: Singal and Systems

11) The _____ time signal is described for all values of time.

a) Discrete

b) Continuous

c) Random

d) Digital

12 / 30

Category: Power System Analysis

12) Power in AC circuit is found by

a) VI sin (phi)

b) VI tan (phi)

c) VI cos (phi)

d) VI

13 / 30

Category: Power Electroncis

13) If the firing angle in an SCR rectifier is decreased, output will be

a) Maximum

b) Increased

c) Decreased

d) Unaffected

14 / 30

Category: Telecommunications

14) Modulation index in amplitude modulation

a) Is defined as the measure of extent of amplitude variation about an un-modulated carrier.

b) Does not impact power dissipation

c) Is independent of integral multiple of amplitude

d) None of these

15 / 30

Category: Basic Electrical Engineering

15) Which line is obtained by the method of least square?

a) Straight line

b) Second degree equation line

c) Polynomial equation line

d) Best fit line

16 / 30

Category: Electrical Machines

16) A transformer transforms

a) Voltage

b) Power

c) Frequency

d) Current

e) Both A & D

17 / 30

Category: Basic Electrical Engineering

17) If the input capacitor of a power supply is shorted, it will result in

a) Excessive hum

b) Reduced voltage output

c) No voltage output

d) Low voltage output

18 / 30

Category: Electroncis

18) SCR (Silicon Controlled Rectifier) goes into saturation, when gate-cathode junction is

a) Forward biased

b) Reversed biased

c) In steady state

d) Polarized

19 / 30

Category: Power Transmission and Distributions

19) For which purpose bundled conductors are employed to a power system

a) Appearance of the transmission line

b) Mechanical stability of the line

c) Decrease system stability

d) Increase the short circuit current

20 / 30

Category: Electroncis

20) A semiconductor device is connected in a series circuit with a battery and a resistance. If the polarity of battery is reversed, the current drops almost to zero. The device may be

a) P-type semiconductor

b) N-type semiconductor

c) P-N junction

d) An intrinsic semiconductor

We have to maintain flatness of the surface.

21 / 30

Category: Power System Analysis

21) Which of the following are considered as disadvantages(s) of Gauss-Seidel method over Newton Raphson method in load flow analysis?

a) More iteration

b) More memory requirement and less accuracy

c) Less iteration but more memory

d) More accuracy and more memory

22 / 30

Category: Probability

22) What is the probability of a number "2" when a dice is thrown?

a) 2/6

b) 1/3

c) 1/6

d) 1/4

23 / 30

Category: Basic Electrical Engineering

23) At very sunny places this source(s) of energy can be found

a) Jet fuel

b) Geothermal

c) Solar

d) Both B & C

24 / 30

Category: Network Analysis

24) Admittance is the reciprocal of

a) Capacitive reactance

b) Inductive reactance

c) Reactive power

d) Impedance

25 / 30

Category: Basic Electrical Engineering

25) Fourier series are infinite series of elementary trigonometric functions i.e. Sine and

a) Cosine

b) Sec

c) Cosec

d) Tan

26 / 30

Category: Power System Analysis

26) The quantity "Rm" which relates dependent voltage to controlling current is called

a) Trans Conductance

b) Maximum Resistance

c) Trans Resistance

d) Limiting Resistance

27 / 30

Category: Electrical Machines

27) Fundamental property used in single node pair circuit analyzer is that ______ across all elements is same.

a) Current

b) Voltage

c) Resistance

d) Inductance

28 / 30

Category: Power Transmission and Distributions

28) Drop out to cut off ratio for most relays is of the order of

a) 0.2 to 0.3

b) 0.3 to 0.4

c) 0.4 to 0.6

d) 0.6 to 1.0

We have to maintain flatness of the surface.

29 / 30

Category: DC Machines

29) The Pole Shoes of DC Machines are fastened to the pole core by:

a) Welding

b) Soldering

c) Countersunk Screws

d) Steel Clumps

30 / 30

Category: Power Plant

30) If field resistance of DC shunt generator is increased beyond its critical value, the generator

a) output voltage will exceed its nameplate rating

b) will not build up

c) may burn out if loaded to its nameplate rating

d) power output may exceed its nameplate rating

Your score is

The average score is 28%

Free Udemy Course With Certification
Free certification course for student so that he can enlarge his skills and get certification
📣 Note: All Courses Are Free For 1000 Enrolls Only. After That Coupons Will Not Apply. So Enroll Course ASAP