Post Views: 4

Lead Magnet Course 2023: Killer Lead Magnet for B2B Success

Unlocking the Power of Lead Magnet 2023: Step-by-Step Guide to Effective Lead Generation for Small Businesses, Startups

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

If YOU are an Electrical Engineer then following quiz is for YOU

Electrical Engineering

Smart Series Quiz-1

These questions are taken from smart series book which covers all the subjects of Electrical Engineering and Technology Field

1 / 30

Category: Electrical Machines

1) Fundamental property used in single node pair circuit analyzer is that ______ across all elements is same.

a) Current

b) Voltage

c) Resistance

d) Inductance

2 / 30

Category: Power System Analysis

2) Power in AC circuit is found by

a) VI sin (phi)

b) VI tan (phi)

c) VI cos (phi)

d) VI

3 / 30

Category: Network Analysis

3) Admittance is the reciprocal of

a) Capacitive reactance

b) Inductive reactance

c) Reactive power

d) Impedance

4 / 30

Category: Electroncis

4) A semiconductor device is connected in a series circuit with a battery and a resistance. If the polarity of battery is reversed, the current drops almost to zero. The device may be

a) P-type semiconductor

b) N-type semiconductor

c) P-N junction

d) An intrinsic semiconductor

5 / 30

Category: Power System Analysis

5) There are ____ types of dependent sources, depending on the controlling variable and output of the source.

a) Two

b) Three

c) Four

d) Five

6 / 30

Category: Probability

6) What is the probability of a number “2” when a dice is thrown?

a) 2/6

b) 1/3

c) 1/6

d) 1/4

7 / 30

Category: Electrical Machines

7) Radio frequency chokes are air cored to

a) Keep frequency low

b) Keep inductive reactance low

c) Keep frequency high

d) Keep inductive reactance high

8 / 30

Category: Power Plant

8) ______ is a by-product of paper industry, which is used by many industries as a primary source of electricity.

a) Landfill gas

b) Sludge waste

c) Black Liquor

d) Wood waste

9 / 30

Category: Power Plant

9) Landfill gas is actually _______ used in thermal power plants.

a) Methane

b) Ethane

c) Black Liquor

d) Phosphorus

We have to maintain flatness of the surface.

10 / 30

Category: Power System Analysis

10) Which of the following are considered as disadvantages(s) of Gauss-Seidel method over Newton Raphson method in load flow analysis?

a) More iteration

b) More memory requirement and less accuracy

c) Less iteration but more memory

d) More accuracy and more memory

11 / 30

Category: Power System Analysis

11) Which of the following ideas means deciding at runtime what strategy to summon?

a) Dynamic typing

b) Dynamic hiding

c) Dynamic loading

d) Dynamic blinding

12 / 30

Category: Power Plant

12) If field resistance of DC shunt generator is increased beyond its critical value, the generator

a) output voltage will exceed its nameplate rating

b) will not build up

c) may burn out if loaded to its nameplate rating

d) power output may exceed its nameplate rating

13 / 30

Category: Power Electroncis

13) If the firing angle in an SCR rectifier is decreased, output will be

a) Maximum

b) Increased

c) Decreased

d) Unaffected

14 / 30

Category: Telecommunications

14) Modulation index in amplitude modulation

a) Is defined as the measure of extent of amplitude variation about an un-modulated carrier.

b) Does not impact power dissipation

c) Is independent of integral multiple of amplitude

d) None of these

15 / 30

Category: Power Transmission and Distributions

15) For which purpose bundled conductors are employed to a power system

a) Appearance of the transmission line

b) Mechanical stability of the line

c) Decrease system stability

d) Increase the short circuit current

16 / 30

Category: Power Transmission and Distributions

16) Which of the following conditions relate line resistance ‘R’ and line reactance ‘X’ for maximum steady state power transmission on a transmission line?

a) X=R

b) R=[Square Root (3)]*X

c) X=[Square Root (3)]*R

d) X=R / [Square Root (3)]

17 / 30

Category: Singal and Systems

17) Main purpose of modulation process is to

a) Distort the original signal

b) Add extra noise to the signal

c) Reduce the mutual interference

d) Time shift in frequency

e) Increase signal to noise ratio

We have to maintain flatness of the surface.

18 / 30

Category: DC Machines

18) The Pole Shoes of DC Machines are fastened to the pole core by:

a) Welding

b) Soldering

c) Countersunk Screws

d) Steel Clumps

19 / 30

Category: Basic Electrical Engineering

19) If the input capacitor of a power supply is shorted, it will result in

a) Excessive hum

b) Reduced voltage output

c) No voltage output

d) Low voltage output

20 / 30

Category: Basic Electrical Engineering

20) Fourier series are infinite series of elementary trigonometric functions i.e. Sine and

a) Cosine

b) Sec

c) Cosec

d) Tan

21 / 30

Category: Electrical Machines

21) A transformer transforms

a) Voltage

b) Power

c) Frequency

d) Current

e) Both A & D

22 / 30

Category: Singal and Systems

22) The _____ time signal is described for all values of time.

a) Discrete

b) Continuous

c) Random

d) Digital

23 / 30

Category: Basic Electrical Engineering

23) Conjunction x ^ y behaves on digits 0 and 1 exactly as ____ does for ordinary algebra.

a) Addition

b) Subtraction

c) Multiplication

d) Division

24 / 30

Category: Power Plant

24) The average fossil fuel plant convers about is ______ % of the power going in to the power going out.

a) 33

b) 40

c) 25

d) 50

25 / 30

Category: Electroncis

25) SCR (Silicon Controlled Rectifier) goes into saturation, when gate-cathode junction is

a) Forward biased

b) Reversed biased

c) In steady state

d) Polarized

26 / 30

Category: Basic Electrical Engineering

26) At very sunny places this source(s) of energy can be found

a) Jet fuel

b) Geothermal

c) Solar

d) Both B & C

27 / 30

Category: Electroncis

27) Discrete device field effect transistor is classified on the basis of their

a) Resistive state

b) Conducting state

c) Voltaic state

d) Control gate construction

28 / 30

Category: Power System Analysis

28) The quantity “Rm” which relates dependent voltage to controlling current is called

a) Trans Conductance

b) Maximum Resistance

c) Trans Resistance

d) Limiting Resistance

29 / 30

Category: Power Transmission and Distributions

29) Drop out to cut off ratio for most relays is of the order of

a) 0.2 to 0.3

b) 0.3 to 0.4

c) 0.4 to 0.6

d) 0.6 to 1.0

30 / 30

Category: Basic Electrical Engineering

30) Which line is obtained by the method of least square?

a) Straight line

b) Second degree equation line

c) Polynomial equation line

d) Best fit line

Your score is

The average score is 28%

Enroll Now

More Courses

Lead Magnet Course 2023: Killer Lead Magnet for B2B Success

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

If YOU are an Electrical Engineer then following quiz is for YOU

Like this:

Related

Leave a Comment Cancel Reply

Lead Magnet Course 2023: Killer Lead Magnet for B2B Success

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

If YOU are an Electrical Engineer then following quiz is for YOU

Share this:

Like this:

Related

Related Posts

Leave a Comment Cancel Reply