Fundamentals of Financial Services

Understanding key elements and basic workings of the Financial Services Industry (useful for exams as well)

1000 Coupons are used

24 hours passed

If YOU are an Electrical Engineer then following quiz is for YOU

Electrical Engineering

Smart Series Quiz-1

These questions are taken from smart series book which covers all the subjects of Electrical Engineering and Technology Field

1 / 30

Category: Power Transmission and Distributions

1) For which purpose bundled conductors are employed to a power system

a) Appearance of the transmission line

b) Mechanical stability of the line

c) Decrease system stability

d) Increase the short circuit current

2 / 30

Category: Electrical Machines

2) Radio frequency chokes are air cored to

a) Keep frequency low

b) Keep inductive reactance low

c) Keep frequency high

d) Keep inductive reactance high

3 / 30

Category: Electroncis

3) SCR (Silicon Controlled Rectifier) goes into saturation, when gate-cathode junction is

a) Forward biased

b) Reversed biased

c) In steady state

d) Polarized

4 / 30

Category: Basic Electrical Engineering

4) Conjunction x ^ y behaves on digits 0 and 1 exactly as ____ does for ordinary algebra.

a) Addition

b) Subtraction

c) Multiplication

d) Division

5 / 30

Category: Electroncis

5) Discrete device field effect transistor is classified on the basis of their

a) Resistive state

b) Conducting state

c) Voltaic state

d) Control gate construction

6 / 30

Category: Power Plant

6) ______ is a by-product of paper industry, which is used by many industries as a primary source of electricity.

a) Landfill gas

b) Sludge waste

c) Black Liquor

d) Wood waste

7 / 30

Category: Power Transmission and Distributions

7) Drop out to cut off ratio for most relays is of the order of

a) 0.2 to 0.3

b) 0.3 to 0.4

c) 0.4 to 0.6

d) 0.6 to 1.0

8 / 30

Category: Electrical Machines

8) A transformer transforms

a) Voltage

b) Power

c) Frequency

d) Current

e) Both A & D

9 / 30

Category: Basic Electrical Engineering

9) Which line is obtained by the method of least square?

a) Straight line

b) Second degree equation line

c) Polynomial equation line

d) Best fit line

10 / 30

Category: Singal and Systems

10) Main purpose of modulation process is to

a) Distort the original signal

b) Add extra noise to the signal

c) Reduce the mutual interference

d) Time shift in frequency

e) Increase signal to noise ratio

11 / 30

Category: Singal and Systems

11) The _____ time signal is described for all values of time.

a) Discrete

b) Continuous

c) Random

d) Digital

12 / 30

Category: Network Analysis

12) Admittance is the reciprocal of

a) Capacitive reactance

b) Inductive reactance

c) Reactive power

d) Impedance

13 / 30

Category: Probability

13) What is the probability of a number “2” when a dice is thrown?

a) 2/6

b) 1/3

c) 1/6

d) 1/4

14 / 30

Category: Power Plant

14) Landfill gas is actually _______ used in thermal power plants.

a) Methane

b) Ethane

c) Black Liquor

d) Phosphorus

15 / 30

Category: Telecommunications

15) Modulation index in amplitude modulation

a) Is defined as the measure of extent of amplitude variation about an un-modulated carrier.

b) Does not impact power dissipation

c) Is independent of integral multiple of amplitude

d) None of these

16 / 30

Category: Power Plant

16) The average fossil fuel plant convers about is ______ % of the power going in to the power going out.

a) 33

b) 40

c) 25

d) 50

17 / 30

Category: Power System Analysis

17) Which of the following ideas means deciding at runtime what strategy to summon?

a) Dynamic typing

b) Dynamic hiding

c) Dynamic loading

d) Dynamic blinding

18 / 30

Category: Power System Analysis

18) Power in AC circuit is found by

a) VI sin (phi)

b) VI tan (phi)

c) VI cos (phi)

d) VI

19 / 30

Category: Power Plant

19) If field resistance of DC shunt generator is increased beyond its critical value, the generator

a) output voltage will exceed its nameplate rating

b) will not build up

c) may burn out if loaded to its nameplate rating

d) power output may exceed its nameplate rating

20 / 30

Category: Basic Electrical Engineering

20) Fourier series are infinite series of elementary trigonometric functions i.e. Sine and

a) Cosine

b) Sec

c) Cosec

d) Tan

21 / 30

Category: Basic Electrical Engineering

21) If the input capacitor of a power supply is shorted, it will result in

a) Excessive hum

b) Reduced voltage output

c) No voltage output

d) Low voltage output

22 / 30

Category: Power System Analysis

22) There are ____ types of dependent sources, depending on the controlling variable and output of the source.

a) Two

b) Three

c) Four

d) Five

23 / 30

Category: Basic Electrical Engineering

23) At very sunny places this source(s) of energy can be found

a) Jet fuel

b) Geothermal

c) Solar

d) Both B & C

24 / 30

Category: Power Transmission and Distributions

24) Which of the following conditions relate line resistance ‘R’ and line reactance ‘X’ for maximum steady state power transmission on a transmission line?

a) X=R

b) R=[Square Root (3)]*X

c) X=[Square Root (3)]*R

d) X=R / [Square Root (3)]

25 / 30

Category: Power Electroncis

25) If the firing angle in an SCR rectifier is decreased, output will be

a) Maximum

b) Increased

c) Decreased

d) Unaffected

26 / 30

Category: Electrical Machines

26) Fundamental property used in single node pair circuit analyzer is that ______ across all elements is same.

a) Current

b) Voltage

c) Resistance

d) Inductance

27 / 30

Category: Power System Analysis

27) The quantity “Rm” which relates dependent voltage to controlling current is called

a) Trans Conductance

b) Maximum Resistance

c) Trans Resistance

d) Limiting Resistance

We have to maintain flatness of the surface.

28 / 30

Category: DC Machines

28) The Pole Shoes of DC Machines are fastened to the pole core by:

a) Welding

b) Soldering

c) Countersunk Screws

d) Steel Clumps

We have to maintain flatness of the surface.

29 / 30

Category: Power System Analysis

29) Which of the following are considered as disadvantages(s) of Gauss-Seidel method over Newton Raphson method in load flow analysis?

a) More iteration

b) More memory requirement and less accuracy

c) Less iteration but more memory

d) More accuracy and more memory

30 / 30

Category: Electroncis

30) A semiconductor device is connected in a series circuit with a battery and a resistance. If the polarity of battery is reversed, the current drops almost to zero. The device may be

a) P-type semiconductor

b) N-type semiconductor

c) P-N junction

d) An intrinsic semiconductor

Your score is

The average score is 28%

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

Enroll Now

More Courses

Fundamentals of Financial Services

1000 Coupons are used

24 hours passed

If YOU are an Electrical Engineer then following quiz is for YOU

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

Like this:

Related

Leave a Comment Cancel Reply

Fundamentals of Financial Services

1000 Coupons are used

24 hours passed

If YOU are an Electrical Engineer then following quiz is for YOU

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

Share this:

Like this:

Related

Leave a Comment Cancel Reply