Learn Microsoft Publisher | Complete Microsoft Publisher

Learn the Beginner to Expert Level Microsoft Publisher Training Course | A Complete Guide to Microsoft Publisher

These course coupons are offered by the official website and we do not have any type of ownership of courses.

If YOU are an Electrical Engineer then following quiz is for YOU

Electrical Engineering

Smart Series Quiz-1

These questions are taken from smart series book which covers all the subjects of Electrical Engineering and Technology Field

1 / 30

Category: Power Plant

1) The average fossil fuel plant convers about is ______ % of the power going in to the power going out.

a) 33

b) 40

c) 25

d) 50

2 / 30

Category: Power System Analysis

2) The quantity “Rm” which relates dependent voltage to controlling current is called

a) Trans Conductance

b) Maximum Resistance

c) Trans Resistance

d) Limiting Resistance

3 / 30

Category: Power System Analysis

3) There are ____ types of dependent sources, depending on the controlling variable and output of the source.

a) Two

b) Three

c) Four

d) Five

4 / 30

Category: Power System Analysis

4) Which of the following ideas means deciding at runtime what strategy to summon?

a) Dynamic typing

b) Dynamic hiding

c) Dynamic loading

d) Dynamic blinding

5 / 30

Category: Basic Electrical Engineering

5) Conjunction x ^ y behaves on digits 0 and 1 exactly as ____ does for ordinary algebra.

a) Addition

b) Subtraction

c) Multiplication

d) Division

6 / 30

Category: Basic Electrical Engineering

6) Fourier series are infinite series of elementary trigonometric functions i.e. Sine and

a) Cosine

b) Sec

c) Cosec

d) Tan

7 / 30

Category: Power Electroncis

7) If the firing angle in an SCR rectifier is decreased, output will be

a) Maximum

b) Increased

c) Decreased

d) Unaffected

8 / 30

Category: Power Transmission and Distributions

8) For which purpose bundled conductors are employed to a power system

a) Appearance of the transmission line

b) Mechanical stability of the line

c) Decrease system stability

d) Increase the short circuit current

9 / 30

Category: Electroncis

9) Discrete device field effect transistor is classified on the basis of their

a) Resistive state

b) Conducting state

c) Voltaic state

d) Control gate construction

10 / 30

Category: Power Plant

10) ______ is a by-product of paper industry, which is used by many industries as a primary source of electricity.

a) Landfill gas

b) Sludge waste

c) Black Liquor

d) Wood waste

11 / 30

Category: Telecommunications

11) Modulation index in amplitude modulation

a) Is defined as the measure of extent of amplitude variation about an un-modulated carrier.

b) Does not impact power dissipation

c) Is independent of integral multiple of amplitude

d) None of these

12 / 30

Category: Singal and Systems

12) The _____ time signal is described for all values of time.

a) Discrete

b) Continuous

c) Random

d) Digital

13 / 30

Category: Singal and Systems

13) Main purpose of modulation process is to

a) Distort the original signal

b) Add extra noise to the signal

c) Reduce the mutual interference

d) Time shift in frequency

e) Increase signal to noise ratio

14 / 30

Category: Electroncis

14) SCR (Silicon Controlled Rectifier) goes into saturation, when gate-cathode junction is

a) Forward biased

b) Reversed biased

c) In steady state

d) Polarized

15 / 30

Category: Power Transmission and Distributions

15) Which of the following conditions relate line resistance ‘R’ and line reactance ‘X’ for maximum steady state power transmission on a transmission line?

a) X=R

b) R=[Square Root (3)]*X

c) X=[Square Root (3)]*R

d) X=R / [Square Root (3)]

16 / 30

Category: Basic Electrical Engineering

16) Which line is obtained by the method of least square?

a) Straight line

b) Second degree equation line

c) Polynomial equation line

d) Best fit line

17 / 30

Category: Electroncis

17) A semiconductor device is connected in a series circuit with a battery and a resistance. If the polarity of battery is reversed, the current drops almost to zero. The device may be

a) P-type semiconductor

b) N-type semiconductor

c) P-N junction

d) An intrinsic semiconductor

18 / 30

Category: Basic Electrical Engineering

18) At very sunny places this source(s) of energy can be found

a) Jet fuel

b) Geothermal

c) Solar

d) Both B & C

19 / 30

Category: Electrical Machines

19) Radio frequency chokes are air cored to

a) Keep frequency low

b) Keep inductive reactance low

c) Keep frequency high

d) Keep inductive reactance high

20 / 30

Category: Power Plant

20) Landfill gas is actually _______ used in thermal power plants.

a) Methane

b) Ethane

c) Black Liquor

d) Phosphorus

21 / 30

Category: Power Plant

21) If field resistance of DC shunt generator is increased beyond its critical value, the generator

a) output voltage will exceed its nameplate rating

b) will not build up

c) may burn out if loaded to its nameplate rating

d) power output may exceed its nameplate rating

22 / 30

Category: Network Analysis

22) Admittance is the reciprocal of

a) Capacitive reactance

b) Inductive reactance

c) Reactive power

d) Impedance

23 / 30

Category: Power Transmission and Distributions

23) Drop out to cut off ratio for most relays is of the order of

a) 0.2 to 0.3

b) 0.3 to 0.4

c) 0.4 to 0.6

d) 0.6 to 1.0

24 / 30

Category: Electrical Machines

24) Fundamental property used in single node pair circuit analyzer is that ______ across all elements is same.

a) Current

b) Voltage

c) Resistance

d) Inductance

We have to maintain flatness of the surface.

25 / 30

Category: DC Machines

25) The Pole Shoes of DC Machines are fastened to the pole core by:

a) Welding

b) Soldering

c) Countersunk Screws

d) Steel Clumps

26 / 30

Category: Basic Electrical Engineering

26) If the input capacitor of a power supply is shorted, it will result in

a) Excessive hum

b) Reduced voltage output

c) No voltage output

d) Low voltage output

We have to maintain flatness of the surface.

27 / 30

Category: Power System Analysis

27) Which of the following are considered as disadvantages(s) of Gauss-Seidel method over Newton Raphson method in load flow analysis?

a) More iteration

b) More memory requirement and less accuracy

c) Less iteration but more memory

d) More accuracy and more memory

28 / 30

Category: Power System Analysis

28) Power in AC circuit is found by

a) VI sin (phi)

b) VI tan (phi)

c) VI cos (phi)

d) VI

29 / 30

Category: Electrical Machines

29) A transformer transforms

a) Voltage

b) Power

c) Frequency

d) Current

e) Both A & D

30 / 30

Category: Probability

30) What is the probability of a number “2” when a dice is thrown?

a) 2/6

b) 1/3

c) 1/6

d) 1/4

Your score is

The average score is 28%

Enroll Now

More Courses

Learn Microsoft Publisher | Complete Microsoft Publisher

These course coupons are offered by the official website and we do not have any type of ownership of courses.

If YOU are an Electrical Engineer then following quiz is for YOU

Like this:

Related

Leave a Comment Cancel Reply

Learn Microsoft Publisher | Complete Microsoft Publisher

These course coupons are offered by the official website and we do not have any type of ownership of courses.

If YOU are an Electrical Engineer then following quiz is for YOU

Share this:

Like this:

Related

Leave a Comment Cancel Reply