Learn Java Fundamentals for Beginners

Java Basics and Fundamentals

Disclaimer:

These course coupons are offered by the official website and we do not have any type of ownership of courses.

If YOU are an Electrical Engineer then following quiz is for YOU

0%
2

Electrical Engineering

Simple things to boost your creativity

Smart Series Quiz-1

These questions are taken from smart series book which covers all the subjects of Electrical Engineering and Technology Field

1 / 30

Category: Power Transmission and Distributions

1) Which of the following conditions relate line resistance ‘R’ and line reactance ‘X’ for maximum steady state power transmission on a transmission line?

2 / 30

Category: Telecommunications

2) Modulation index in amplitude modulation

3 / 30

Category: Electrical Machines

3) Radio frequency chokes are air cored to

4 / 30

Category: Basic Electrical Engineering

4) At very sunny places this source(s) of energy can be found

5 / 30

Category: Basic Electrical Engineering

5) Which line is obtained by the method of least square?

We have to maintain flatness of the surface.

6 / 30

Category: Power System Analysis

6) Which of the following are considered as disadvantages(s) of Gauss-Seidel method over Newton Raphson method in load flow analysis?

7 / 30

Category: Basic Electrical Engineering

7) If the input capacitor of a power supply is shorted, it will result in

8 / 30

Category: Network Analysis

8) Admittance is the reciprocal of

9 / 30

Category: Electroncis

9) A semiconductor device is connected in a series circuit with a battery and a resistance. If the polarity of battery is reversed, the current drops almost to zero. The device may be

10 / 30

Category: Power System Analysis

10) There are ____ types of dependent sources, depending on the controlling variable and output of the source.

11 / 30

Category: Power Plant

11) Landfill gas is actually _______ used in thermal power plants.

12 / 30

Category: Basic Electrical Engineering

12) Conjunction x ^ y behaves on digits 0 and 1 exactly as ____ does for ordinary algebra.

13 / 30

Category: Power Transmission and Distributions

13) Drop out to cut off ratio for most relays is of the order of

14 / 30

Category: Power Transmission and Distributions

14) For which purpose bundled conductors are employed to a power system

15 / 30

Category: Electrical Machines

15) A transformer transforms

16 / 30

Category: Electrical Machines

16) Fundamental property used in single node pair circuit analyzer is that ______ across all elements is same.

17 / 30

Category: Power Plant

17) ______ is a by-product of paper industry, which is used by many industries as a primary source of electricity.

18 / 30

Category: Probability

18) What is the probability of a number “2” when a dice is thrown?

19 / 30

Category: Power System Analysis

19) Which of the following ideas means deciding at runtime what strategy to summon?

20 / 30

Category: Power System Analysis

20) Power in AC circuit is found by

21 / 30

Category: Singal and Systems

21) The _____ time signal is described for all values of time.

22 / 30

Category: Basic Electrical Engineering

22) Fourier series are infinite series of elementary trigonometric functions i.e. Sine and

23 / 30

Category: Power Electroncis

23) If the firing angle in an SCR rectifier is decreased, output will be

24 / 30

Category: Power Plant

24) If field resistance of DC shunt generator is increased beyond its critical value, the generator

25 / 30

Category: Singal and Systems

25) Main purpose of modulation process is to

26 / 30

Category: Electroncis

26) SCR (Silicon Controlled Rectifier) goes into saturation, when gate-cathode junction is

27 / 30

Category: Electroncis

27) Discrete device field effect transistor is classified on the basis of their

28 / 30

Category: Power Plant

28) The average fossil fuel plant convers about is ______ % of the power going in to the power going out.

29 / 30

Category: Power System Analysis

29) The quantity “Rm” which relates dependent voltage to controlling current is called

We have to maintain flatness of the surface.

30 / 30

Category: DC Machines

30) The Pole Shoes of DC Machines are fastened to the pole core by:

Your score is

The average score is 28%

Share this quiz with your friends to help them

LinkedIn Facebook
0%

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top